Skip to content
Blue Planet Energy

How it works

Our software splits the demand above a grid limit. Supercapacitors take the brief bursts, batteries take the rest.

Two systems, one set of modules

Both are built from the same sodium-ion energy module and supercapacitor power module, so a site can start small and grow. Each system is sized for its site.

SystemTypical sitesFootprintScale
Rack systemsTelecom sites, network cabinets and smaller commercial buildings, in standard 19-inch racksOne or two racksTens of kilowatt-hours
High-capacity systemsData centers, EV charging hubs, industrial plants and grid supportMultiple bays, added as the site growsHundreds of kilowatt-hours and up

One system, three technologies

Our system combines sodium-ion batteries, supercapacitors and control software, each taking the part of the demand it suits.

Supercapacitors

Store charge as a layer of ions on the electrode surface. They deliver and accept high power within seconds and tolerate very large cycle counts, but hold relatively little energy.

Built for seconds to tens of seconds

Sodium-ion batteries

Store energy by moving sodium ions into and out of the electrode material. They supply the longer part of a demand peak and hold far more energy than the same volume of supercapacitors.

Built for minutes to hours

Controls and software

Compare site demand with the grid limit, send short events to the supercapacitors and sustained demand to the batteries, then recharge both when there is headroom.

Continuous

The software reads site demand and decides which one answers, moment by moment.

Why combine batteries and supercapacitors

  • Peaks come in two speeds.Brief spikes of seconds sit on top of stretches that run for minutes or hours. Batteries and supercapacitors can both deliver high power, so the question is which one should, and when.
  • Frequent high-power cycling adds battery stress.Repeated high-power cycling adds stress to battery cells. Supercapacitors are built for that duty, so the batteries can work at a steadier rate.
  • Sodium is widely available.Sodium-ion cells use no lithium. Sodium compounds are produced in many regions from common raw materials.

How storage connects to a site

Our storage sits on the DC side of a power converter, which moves energy to and from the AC system you already run. We build the batteries, the supercapacitors and the software that decides what happens. The converter and the site wiring come from your integrator, and we design around them.

  • Measurement at the grid connection tells the controls how close the site is to its limit.
  • A bidirectional converter sits between our DC storage and your AC system and sets how fast power moves each way.
  • Protection devices on both the DC and AC sides isolate faults.

Before specifying a system

Ask for specifications and test documents for the exact equipment: usable energy, charge and discharge limits, operating conditions, protection and installation requirements.

How ions and electrons move inside a cell: Battery 101

What the system is built for

Four decisions that shape everything else in the design.

  • Works where the sites are

    Our cell suppliers rate the sodium-ion cells and supercapacitor modules from −40 °C to +65 °C. Arctic cabinets and desert rooftops are the point. The rating for a complete system also depends on its enclosure.

  • Less cooling to pay for

    Cells that run cooler need less cooling around them: less chiller energy, less water, and simpler mechanical work in the building.

  • Materials you can actually get

    The battery cells use no lithium, cobalt or nickel. Sodium compounds are produced in many regions from common raw materials.

  • The hard work off the battery

    Supercapacitors take the fast, high-power events, so the batteries run at a steadier rate instead of chasing every spike.

Proven outside this building

Three independent tracks, run by people who do not work for us. Dr. Zaghib also sits on our advisory board.

  • Review of the cells. Peer review of the sodium-ion and supercapacitor cells by Dr. Karim Zaghib at Concordia University, covering cell chemistry and build quality.
  • Accelerated cycle-life testing. Third-party hardware-in-the-loop testing of the combined architecture, to measure how cells degrade against specification rather than relying on supplier figures.
  • Safety listing and fire testing. Submission for UL 9540 listing and UL 9540A fire-propagation testing at an independent laboratory, the standards that govern how these systems are installed.

Explore a simulated site

The peak-shaving simulator runs this split on four example sites and compares it with a battery-only design.

Open the simulator